Industry standard for potable water epoxy coatings for nearly 40 years. Known for its forgiving application characteristics in adverse and varied conditions, and for its benchmark performance.
Fast-curing protective coating for use in steel and concrete structures. Contact your Tnemec representative for other systems and additional information on potential uses.
High solids, immersion-grade coating offering exceptional build per coat for long-term corrosion resistance. For use on the interior and exterior of steel or concrete tanks, reservoirs, pipes, valves, pumps, and equipment, as well as other steel and concrete substrates. Specially formulated to meet the latest requirements for use in potable water applications.
An advanced generation, 100% solids, high-build epoxy for the protection of steel and concrete. It provides excellent resistance to abrasion and is suitable for immersion service in potable water and wastewater environments. Specialized curing mechanism allows for faster cure response with airless spray application.
An advanced generation, 100% solids epoxy liner for the protection of steel and concrete. It provides excellent resistance to abrasion and is suitable for immersion and chemical contact. For use on the interior and exterior of steel or concrete tanks, reservoirs, and pipes in potable water service.
A unique, low odor, low VOC, water-based epoxy coating featuring HydroLink curing technology for exceptional durability and corrosion resistance. Used for the protection and finishing of steel and concrete structures including structural steel, tanks, pipes, and equipment. Superior wetting for marginally prepared steel and tightly adhered existing coatings. This coating is ideally suited for steel fabrication and OEM applications, with fast-curing and rapid handling properties. Series 27WB exhibits low yellowing and good color stability in whites and light tone colors. Formula protected under U.S. patent.
Versatile coal tar coating for use in immersion, splash and spillage, chemical fumes and below-grade environments.
High-build corrosion resistant coating providing one coat protection for concrete and steel in a variety of chemical, immersion and underground conditions. Also, when a two-coat application is desired, a low film build option is possible.
Single component coating for filling surface voids in porous concrete and masonry block on interior, dry, above-grade masonry surfaces.
Tightly cross-linked epoxy with excellent corrosion and chemical resistance. Principally used for immersion services, including fuel and crude oil storage, fuel pipelines, pressure vessels, chemical containment and wastewater treatment.
Industry standard for epoxy coatings for over 40 years. Known for its forgiving application characteristics in adverse and varied conditions, and for benchmark performance.
Product is made to order for specific projects. Contact your Tnemec Representative for additional information.
A high-solids, low VOC, pure polyamide epoxy that offers exceptional protection to a variety of substrates in atmospheric and immersion environments. Applied as a primer, intermediate, or topcoat, this versatile coating also accepts a wide-range of finish coats, allowing for a coating system tailored to specific exposure conditions.
A versatile, low VOC epoxy for protection and finishing of steel and concrete. It has excellent resistance to abrasion and is suitable for immersion as well as chemical contact exposure. Contact your local Tnemec representative for a list of chemicals. This product can also be used for lining storage tanks that contain demineralized, deionized, or distilled water. Can serve as a block filler on cementitious or masonry substrates.
A versatile, low VOC, factory-accelerated epoxy for protection and finishing of steel and concrete. It has excellent resistance to abrasion and is suitable for immersion as well as chemical contact exposure. Contact your local Tnemec representative for a list of chemicals.
An advanced generation epoxy formulated for the protection of steel, concrete, and ductile iron substrates. It has excellent resistance to abrasion and is suitable for immersion as well as chemical contact exposure. Contact your local Tnemec representative for a list of chemicals and concentrations. This product can also be used for lining storage tanks that contain demineralized, deionized or distilled water.
An advanced generation epoxy formulated for the protection of steel, concrete, and ductile iron substrates. It has excellent resistance to abrasion and is suitable for immersion as well as chemical contact exposure. Contact your local Tnemec representative for a list of chemicals and concentrations. This product can also be used as a block filler on cementitious or masonry substrates.
A coating for commercial, industrial, and marine applications that is highly resistant to abrasion, wet conditions, corrosive fumes, chemical contact and has excellent resistance to exterior weathering. Direct-to-Metal capability allows for a labor-saving, high-build, single coat application.
Versatile coating applies up to 10 mils per coat on steel or concrete. Protects in immersion, salt spray and chemical exposures. Superior abrasion- and stain-resistance.
Series 108 ProBond is a thin-film, low-stress, epoxy designed to adhere to a multitude of substrates, including old finishes, and is frequently used as an overcoating primer. Series 108 is solvent-free and is applied at a low film thickness to reduce stress and weight on old tightly adhered coatings creating a foundation to accept high-performance epoxy and polyurethane finishes. Also used, when specified, as the primer under Lavacrete polymer concrete epoxy toppings. NOT FOR IMMERSION SERVICE. Formerly Series 3600 ProBond. Note: Adhesion analysis of old finishes and test patches are recommended before overcoating a structure. Reference the latest version of Tnemec Technical Bulletin 98-10 for more information.
Series 109 ProBond is a lower-temperature curing, thin-film, low-stress, epoxy designed to adhere to a multitude of substrates, including old finishes, and is frequently used as an overcoating primer. Series 109 is solvent-free and is applied at a low film thickness to reduce stress and weight on old tightly adhered coatings creating a foundation to accept high-performance epoxy and polyurethane finishes. Also used, when specified, as the primer under Lavacrete polymer concrete epoxy toppings. Note: Adhesion analysis of old finishes and test patches are recommended before overcoating a structure. Reference the latest version of Tnemec Technical Bulletin 98-10 for more information.
High performance coating suitable for concrete, steel and other commonly used building materials. Features include high-build, low odor, non-yellowing white and fade resistant colors; easy cleanup and stain-, abrasion-, chemical- and moisture-resistance. Good exterior performance.
High performance gloss coating suitable for concrete, steel and other commonly used building materials. Features include high-build, low odor, non-yellowing white and fade resistant colors; easy cleanup and stain-, abrasion-, chemical- and moisture-resistance. Good exterior performance.
A high-performance, versatile coating appropriate for a variety of uses including: Exterior Steel: Waterborne, rust-inhibitive coating with excellent adhesion to zinc-rich coatings. Used as a primer, intermediate and finish coat on tanks, vessels and other industrial and architectural metal substrates. Humid Environments: Primer/finish for two coat applications over prepared galvanized steel and zinc-rich coatings in wet, temperature-controlled exposure areas. Dry Interior Environments: One or two coat, flash-rust and corrosion resistant primer/finish for overheads. Use on prepared carbon and galvanized steel, aluminum, wood and concrete decks, beams, joists and HVAC. Note: Uni-Bond DF's "dry-fall" characteristics help reduce the potential for overspray problems on buildings and surrounding property.
A high-performance, versatile coating appropriate for a variety of uses including: Exterior Steel: Waterborne, rust-inhibitive coating with excellent adhesion to organic zinc-rich coatings. Used as a primer, intermediate or finish coat on tanks, vessels and other industrial and architectural metal substrates. Humid Environments: Primer/finish for two coat applications over prepared galvanized steel and organic zinc-rich coatings in wet, temperature-controlled exposure areas. Dry Interior Environments: One or two coat, flash-rust and corrosion resistant primer/finish for overheads. Use on prepared carbon and galvanized steel, aluminum, wood and concrete decks, beams, joists and HVAC. Note: Uni Bond DF's "dry-fall" characteristics help reduce the potential for overspray problems on buildings and surrounding property.
A finish coat designed for superior protection against organic and inorganic acids and sour crude when stored at elevated temperatures in insulated tanks. Sprayable lining for tanks and vessels. Provides splash, spillage and fume protection for structural surfaces and secondary containment. Note: Contact your Tnemec representative or Tnemec Technical Services with specific chemical exposures.
A primer designed for superior protection against organic and inorganic acids and sour crude when stored at elevated temperatures in insulated tanks. Sprayable lining for tanks and vessels. Provides splash, spillage and fume protection for structural surfaces and secondary containment. Note: Contact your Tnemec representative or Tnemec Technical Services with specific chemical exposures.
Exceptional filling capabilities for interior/exterior porous concrete and CMU. Seals and primes surface for application of a variety of high performance water- and solvent-based topcoats in moderately severe exposures.
Innovative, low VOC potable water coating which offers high-build edge protection and allows for application at a wide range of temperatures (down to 35°F or 2°C with 44-700 Accelerator). For use on the interior and exterior of steel or concrete tanks, reservoirs, and fittings in potable water service.
Versatile epoxy coating (factory accelerated version of L140) for protection and finishing of steel. It has excellent resistance to abrasion and is suitable for immersion service. This product can be used for lining storage tanks that contain demineralized, deionized, distilled, or potable water.
Innovative potable water coating which offers high-build edge protection and allows for application at a wide range of temperatures (down to 35°F or 2°C with 44-700 Accelerator). For use on the interior and exterior of steel or concrete tanks, reservoirs, pipes, valves, pumps, and equipment in potable water service.
Innovative potable water coating which offers high-build edge protection and allows for application at a wide range of temperatures (down to 35°F or 2°C). For use on the interior and exterior of steel or concrete tanks, reservoirs, pipes, valves, pumps, and equipment in potable water service.
Innovative potable water coating which offers high-build edge protection and allows for application at a wide range of temperatures (down to 35°F or 2°C with 44-700 Accelerator). For use on the interior and exterior of steel or concrete tanks, reservoirs, pipes, valves, pumps and equipment in potable water service.
Innovative potable water coating which offers high-build edge protection and allows for application at a wide range of temperatures (down to 35°F or 2°C). For use on the interior and exterior of steel or concrete tanks, reservoirs, pipes, valves, pumps and equipment in potable water service.
A high-solids lining offering high-build edge protection and long-term durability. Series 141 is abrasion and corrosion-resistant for extended immersion service in crude oil and finished fuels. Used to protect steel and concrete storage tanks, transport tanks, pipelines, and industrial wastewater while increasing service life.
Abrasion resistant, high solids, epoxy coating which offers high-build edge protection and excellent corrosion resistance. Contains glass flake and aluminum oxide for improved film integrity. For use on the interior and exterior of steel or concrete tanks, pipes, and other heavy-duty equipment in industrial service.
Series 154 is a durable, single-component, water-based elastomeric coating that forms a waterproof film over horizontal or vertical concrete surfaces as well as various types of wallboard, wood and tile. It is an excellent choice for areas that receive light to moderate traffic including balconies, walkways, pedestrian bridges, mechanical equipment rooms and other surfaces such as concrete decks that may require protection from weather or water intrusion. Versatile application characteristics allow Series 154 to be applied neat, as a broadcast system, or mixed with aggregate and either applied as slurry or used as a surfacer or filler. Series 154 can also be reinforced using woven or octagonal mesh inlays where crack-bridging or extra durability is needed.
Flexible, breathable coating primarily for concrete and masonry that can fill and bridge minor hairline cracks. Excellent elastomeric protection against driving rain, alternate freezing-thawing and UV light. Series 156 can also be used as a low cohesive stress overcoat for aged oil or alkyd systems.
Flexible, breathable coating primarily for concrete and masonry that can fill and bridge minor hairline cracks. Excellent elastomeric protection against driving rain, alternate freezing-thawing and UV light.
Low temperature-cure, corrosion-resistant coating for protection against abrasion, immersion and mild chemical contact. Fast recoat at 75°F (24°C).
Decorative, high-build protection against weather, driving rain, industrial fumes and alternate freezing-thawing. Formulated to resist mildew growth on the paint film. Available in smooth (Series 180) and sand-texture (Series 181) finishes for concrete, CMU and properly primed steel. Spray application "dry-falls" under certain conditions.
Decorative, high-build protection against weather, driving rain, industrial fumes and alternate freezing-thawing. Formulated to resist mildew growth on the paint film. Available in smooth (Series 180) and sand-texture (Series 181) finishes for concrete, CMU and properly primed steel. Spray application “dry-falls” under certain conditions.
High-solids moisture tolerant epoxy used for priming concrete, wood and drywall. Also as a stand-alone one-coat clear floor sealer. Excellent chemical resistance for a variety of substrates.
A fast-cure, versatile coating that can be used as a penetrating primer or a general duty topcoat for protection against abrasion and mild chemicals. Can be applied in temperatures as low as 35°F (2°C).
Flexible epoxy underlayment for bridging small substrate cracks in concrete and to provide a protective waterproof membrane under aggregate reinforced flooring systems. This flexible basecoat is capable of withstanding 50 mils of differential movement without damaging the system.
Glass-reinforced, flexible epoxy mortar basecoat for bridging small substrate cracks in secondary containment concrete structures. Replaces mortar/slurry basecoat for Series 237SC, 239SC, and 252SC when a flexible basecoat is desired.
Epoxoprime MVT is a unique, moisture-tolerant, two component, low viscosity, high solids epoxy primer designed to reduce moisture vapor emissions and provide alkalinity control for concrete with elevated moisture vapor transmission levels that exceed the acceptable limits of non-breathing resilient and polymer floor topping finishes. Epoxoprime MVT can be applied to properly prepared, 10 day old concrete and withstands moisture vapor transmission up to 15 lbs (per ASTM F 1869) and relative humidity up to 95% (per ASTM F 2170). Epoxoprime MVT has a low perm rating (0.05 perm) and is alkaline insensitive to pH levels of 14.
A high gloss, high build, self-leveling epoxy topping for concrete floors. It imparts an ultra smooth, aesthetically pleasing finish in a variety of colors, while providing protection against various acids and alkalis, abrasion and frequent cleaning.
An advanced generation, 100% solids epoxy filler and surfacer for concrete or steel. Excellent material for surfacing, patching, and filling voids in pitted steel and bug holes and pits in concrete substrates. Generally topcoated with a variety of high-performance epoxies and polyurethanes for use in mild to aggressive exposures.
Series 215ML is a trowel applied, fiberglass mat reinforced, 100% solids polyamine epoxy used as part of a lining system for potable and non-potable ultra-filtration membrane process, backwash, and neutralization basins.
A single-component, ultra rapid setting, hydraulic cementitious resurfacer used to restore deteriorated concrete surfaces or extended with aggregate to make high-strength concrete.
A high-performance, aggregate reinforced material for surfacing, patching and filling voids and bugholes in concrete substrates. Generally topcoated with a variety of high-performance epoxies and polyurethanes for use in mild to aggressive exposures.
A low ambering, multi-purpose epoxy coating with enhanced UV stability and resistance to yellowing. Series N222 can be used as a primer, broadcast, slurry/broadcast, mortar, grout coat, metallic color coat, and topcoat. It provides excellent application properties with good flow and self-leveling characteristics. It protects concrete surfaces from impact and abrasion and has excellent chemical resistance with an aesthetically pleasing appearance.
A low ambering, multi-purpose epoxy coating with enhanced UV stability and resistance to yellowing. Series N223 is a decorative mortar floor-topping system installed at 3/16” to 1/4” thickness. It protects concrete surfaces from impact and abrasion and has excellent chemical resistance with an aesthetically pleasing appearance.
A low ambering, multi-purpose epoxy coating with enhanced UV stability and resistance to yellowing. Series N224 is a customized decorative floor topping utilizing colored flake, broadcast either at random or refusal. It protects concrete surfaces from impact and abrasion and has excellent chemical resistance with an aesthetically pleasing appearance.
Commonly used in facilities that manufacture, process, assemble, package, service, inspect or otherwise handle electrical or electronic parts, assemblies and equipment susceptible to damage by electrostatic discharges which have established, implemented and maintain an Electrostatic Discharge (ESD) Control Program. Also used in data centers, clean room/labs, computer rooms, military/aerospace, avionics, automotive manufacturing or any environments where electrostatic discharge (ESD) is a nuisance or may have damaging effects. Formulated using single wall carbon tube technology specifically designed to provide superior electrical conductivity and enhanced mechanical properties. Ensures permanent and uniform electrical conductivity eliminating “hot spots". Designed for static dissipative resistance in the range of 1x10^6^ to 1x10^9^ (one million to one billion) ohms surface resistance when testing point to point/point to ground for establishing floor resistance values per ANSI/ESD S20.20-2014. Project specifications and application specifics should clearly indicate what resistance range is required. Note: Not intended for industries requiring protection against explosion hazards such as dust, fuels, and solvents or electrically initiated explosive compounds and devices.
A lower viscosity, high-solids, multi-purpose epoxy that can be used as a primer, broadcast, slurry/broadcast, mortar, grout coat, metallic color coat and topcoat. Especially useful when penetration is needed to sufficiently anchor epoxy flooring systems over lightly profiled concrete surfaces. Protects concrete surfaces from impact, abrasion and has very good chemical resistance.
A multi-purpose resin for fiberglass reinforced mat (65 mils) or mortar/fiberglass reinforced mat (125 mils) secondary containment systems. Protects against chemicals, thermal cycling, impact and abrasion.
A multi-purpose epoxy coating that can be used as a primer, broadcast, slurry/broadcast, mortar, grout coat, and topcoat. Excellent application properties with good flow and self-leveling characteristics. Protects concrete surfaces from impact, abrasion and mild chemicals.
A chemical resistant, multi-purpose novolac epoxy coating that can be used as a primer, broadcast, slurry/broadcast, mortar, grout coat, and topcoat. Excellent application properties with good flow and self-leveling characteristics. Protects concrete surfaces from impact, abrasion and mild chemicals.
Ultra-Tread S is a low odor, slurry applied, flowable mortar floor topping designed for monolithic applications in abusive service areas. It provides superior performance to other flooring systems such as acid brick, quarry tile and most polymer flooring systems. Designed for use in food and beverage facilities, pharmaceutical and processing areas, commercial and restaurant kitchens or anywhere a durable floor topping is required. Provides excellent chemical resistance and withstands thermal shock due to hot liquids and aggressive cleaning procedures. Areas may be quickly returned to service within hours of installation, depending on temperature and humidity. Ultra-Tread S is a self-priming base coat that can be applied to 10 day old concrete. It can withstand moisture vapor transmission up to 20 lbs (per ASTM F 1869) and relative humidity up to 99% (per ASTM F 2170).
Extremely hard, chemical-resistant urethane floor coating with superb flow characteristics. Excellent resistance to abrasion, wet conditions, corrosive fumes and chemical contact. Excellent gloss and color retention. Low odor characteristic allows for use near occupied space. Note: For horizontal surfaces only.
Extremely hard, chemical-resistant urethane floor coating with superb wear characteristics. Excellent resistance to abrasion, wet conditions, corrosive fumes and chemical contact. Excellent gloss and color retention. Low odor characteristic allows for use near occupied space.
Extremely hard, chemical-resistant, electrostatic dissipative urethane floor coating with superb wear characteristics. Excellent resistance to abrasion, wet conditions, corrosive fumes and chemical contact. Commonly used in facilities that manufacture, process, assemble, package, service, inspect or otherwise handle electrical or electronic parts, assemblies and equipment susceptible to damage by electrostatic discharges which have established, implemented and maintain an Electrostatic Discharge (ESD) Control Program. Also used in data centers, clean room/labs, computer rooms, military/aerospace, avionics, automotive manufacturing or any environments where electrostatic discharge (ESD) is a nuisance or may have damaging effects. Ensures permanent and uniform electrical conductivity eliminating “hot spots". Designed for static dissipative resistance in the range of 1x10^6^ to 1x10^9^ (one million to one billion) ohms surface resistance when testing point to point/point to ground for establishing floor resistance values per ANSI/ESD S20.20. Project specifications and application specifics should clearly indicate what resistance range is required. Note: Not intended for industries requiring protection against explosion hazards such as dust, fuels, and solvents or electrically initiated explosive compounds and devices.
A chemical resistant primer for use with Series 252SC secondary containment system. Note: Contact your Tnemec representative or Tnemec Technical Services with specific chemical exposures.
A highly chemical resistant, multi-purpose resin for fiberglass reinforced mat (65 mils) or mortar/fiberglass reinforced mat (125 mils) secondary containment systems. Protects against harsh chemicals, thermal cycling, impact and abrasion.
An extremely fast-curing, multi-purpose and finish coat resin with low temperature cure capability. Used to build aggregate, colored quartz or decorative flake filled floor topping systems. It can also be used as a clear or pigmented finish coat over systems built using Series 256 or systems built using epoxy, or polyurethane modified concrete floor toppings that have been fully broadcast with aggregate, colored quartz or colored flake. Series 256 will provide protection against impact, abrasion and mild chemicals, has excellent gloss and color retention, and resistance to yellowing. This low VOC, 100% solids urethane exhibits low odor characteristics allowing for use near occupied spaces.
A slower setting Polyaspartic floor coating, offering longer working time and lower viscosity. Series 257 minimizes the potential for lap marks and roller lines when used in large flooring applications. It can be used as a two coat thin-film system or as a clear or pigmented finish coat over systems built using epoxy or polyurethane modified concrete floor toppings that have been fully broadcast with aggregate, colored quartz or colored flake. Series 257 will provide protection against impact, abrasion and mild chemicals, has excellent gloss and color retention, and resistance to yellowing. This low VOC, 100% solids urethane exhibits low odor characteristics allowing for use near occupied spaces.
A chemically active, low VOC solution used to assist in the adhesion of Series 262, 264, and 265 coatings to non-porous substrates like metal, glass, plastics, fiberglass, and tile when recoating with itself if maximum cure time has been exceeded.
Chemical- and abrasion-resistant elastomeric membrane with exceptional strength and flexibility. Ideally suited for environmental requirements of waste containment for primary or secondary containment. Spray applied, it forms the monolithic, impermeable liner required for earth collection and catch basins, decorative ponds and fountains, reservoirs, cooling towers, dams and spillways.
Flexible liner providing a seamless monolithic membrane for use in potable water basins, steel tank floors and reservoirs. Also for areas requiring impermeability such as decorative ponds and secondary chemical containment.
A trowel-grade compound for use with Elasto-Shield products. Used to fill and repair cracks, bugholes, spalled or otherwise damaged concrete, masonry and asphalt. Also used for sealing the edges of faying surfaces, sealing seams, filling pits and encapsulating rivet and bolt heads on the interior of steel tanks.
A high-performance, fiberglass-reinforced wall coating for protection against acids, alkalis and physical abuse. Stranlok’s 100% solids epoxy technology is solventless and VOC compliant, making Stranlok virtually odorless and permitting application in occupied facilities. Its accelerated curing schedule and installation process mean faster return-to-service times. A unique blend of two types of premixed reinforcing fibers allows Stranlok to be spray or trowel applied up to 40 mils. The integrity of the interlocking fibers allows the surface to withstand daily high-pressure steam cleaning. In addition to this high tolerance to “thermal shock,” Stranlok also features broad chemical, impact and abrasion resistance.
A fiberglass mat reinforced coatings system for walls and ceilings providing cleanability and protection against chemical and physical abuse. Provides a high-performance, smooth, seamless surface with excellent chemical, stain, impact and abrasion resistance.
A glaze-like corrosion resistant coating for walls, ceilings, floors and other surfaces; resistant to frequent pressurized hot water and detergent cleaning. Used as a topcoat/sealer for heavy duty wall and floor systems or in a stand-alone high-performance function. Excellent chemical, stain- and abrasion-resistance for a variety of substrates.
A fast-cure glaze-like corrosion resistant coating for walls, ceilings, floors and other surfaces; resistant to frequent pressurized hot water and detergent cleaning. Used as a topcoat/sealer for heavy duty wall and floor systems or in a stand-alone high-performance function. Excellent chemical, stain- and abrasion-resistance for a variety of substrates.
A high-gloss, glaze-like coating for concrete floors. It imparts a smooth, aesthetically pleasing finish in a variety of colors, while providing protection against various acids and alkalis, abrasion and frequent cleaning.
A highly chemical- and solvent-resistant colored novolac glaze coating for walls, floors and other surfaces. Provides improved aesthetics and additional protection against abrasion, impact, and most acids, alkalis and solvents.
A clear, thixotropic binder resin. Series N283 is designed to be used in all phases of cove building or vertical trowel applications (priming, base coat, and topcoat) and it can also be used for concrete repair. Note: When using Series N283 for building cove or troweled wall applications an aggregate similar to 30/50 mesh silica sand, Series 222 or 223 Quartz must be used. Has excellent adhesion, good chemical resistance, repairs concrete, and can be applied up to 1/4” without sagging.
A low ambering, multi-purpose epoxy coating with enhanced UV stability and resistance to yellowing. Series N284 is a clear finish for decorative flooring systems. It protects concrete surfaces from impact and abrasion and has excellent chemical resistance with an aesthetically pleasing appearance.
A clear finish with an orange peel texture for diffusing light and reducing glare. Used as an optional finish for decorative color quartz or flake-filled flooring systems. It protects concrete surfaces from impact and abrasion and has excellent chemical resistance with an aesthetically pleasing appearance. Coves and Vertical Surfaces: Series N285 can be used to build grout and seal vertical surfaces such as 4” base and wainscot.
A clear novolac finish for decorative flooring systems. It protects against harsh chemicals, impact and abrasion, providing a skid-resistant or smooth finish depending on the number of coats.
A low odor, rapid cure, wear-resistant coating for floors, walls and other substrates, capable of withstanding moderate commercial and industrial environments. It can withstand mild to moderate chemical and solvent exposures, as well as repeated cleaning. Can also be used as a primer or intermediate coat for thin film epoxy and urethane and acrylic systems.
Extremely hard, chemical-resistant urethane coating for applications in commercial, industrial, and marine environments with excellent resistance to abrasion, washdown conditions, corrosive fumes and chemical contact. Gloss retention among the best of air dried finishes.
Extremely hard, chemical-resistant urethane coating with excellent abrasion resistance, wash-down conditions, corrosive fumes, and chemical contact.
Extremely hard, chemical-resistant polyurethane floor coating with superb flow characteristics. Excellent resistance to abrasion, wet conditions, corrosive fumes and chemical contact. Gloss and color retention among the best of air dried finishes. Note: For horizontal surfaces only.
Durable, chemical-resistant clear urethane floor coating used as a finish coat for a variety of floor coating systems. It has excellent resistance to abrasion, wet conditions, corrosive fumes and chemical contact. Typically used over epoxy and urethane flooring systems for increased abrasion and chemical resistance and a low-sheen appearance. Contains a blend of ultraviolet (UV) light absorbers for enhanced gloss retention and resistance to UV degradation.
Extremely hard, chemical-resistant clear urethane floor coating used as a finish coat for a variety of floor coating systems. It has superb flow characteristics, excellent resistance to abrasion, wet conditions, corrosive fumes and chemical contact. Gloss among the best of air dried finishes. Typically used over epoxy and urethane flooring systems for increased abrasion and chemical resistance. Contains a blend of ultraviolet (UV) light absorbers for enhanced gloss retention and resistance to UV degradation.
A clear, low odor, fast dry, low VOC, waterborne polyurethane floor coating for interior wall and floor applications. Provides enhanced abrasion resistance and stain resistance. This user friendly product has easy application and clean-up characteristics and may be applied over a properly prepared aged coating (test patch is recommended for compatibility). Contact your Tnemec representative for more details.
Low odor, fast dry, low VOC, waterborne polyurethane coating for wall and floor applications. Provides enhanced abrasion resistance, stain resistance and color stability. This user friendly product has easy application and clean-up characteristics and may be applied over a properly prepared aged coating (test patch is recommended for compatibility). Contact your Tnemec representative for more details.
An epoxy lining formulated for corrosion control and aggressive chemical immersion in pressurized vessels, pipelines, storage tanks, industrial wastewater, etc. Series 370 exhibits superior resistance to a wide range of chemicals with excellent physical properties for long term durability and service life, and offers convenient airless spray application for both field and shop. Contains micro-fiber reinforcement for improved film integrity. Note: Application, environmental and design factors, chemical temperatures, and chemical mixtures can significantly impact coating performance, so due care should be exercised in the selection and use of the coating. Contact your Tnemec representative to review full project details before coating is selected.
A two-component, fast-setting, monolithic coating designed to provide a durable polyurethane lining in a single-coat, multi-pass spray application applied with plural component equipment. This high-performance coating has excellent chemical, thermal shock, and abrasion resistance. It is ideal for application to steel or concrete in water and wastewater treatment, secondary containment, and for tank linings and bottoms. Recommended for immersion service. Note: All orders are subject to approval based upon project scope, applicator qualification, and appropriate equipment configuration.
A 100% solids, hybrid epoxy mortar designed for severe wastewater immersion and fume environments. Specifically formulated to withstand high levels of hydrogen sulfide gas (H2S), sulfuric acid (H2SO4), as well as other gases common to sewer exposures and severe wastewater environments. Aggregate reinforcement provides additional resistance to abrasion and impact.
A versatile, thick film, 100% solids, abrasion-resistant lining specifically designed for domestic wastewater immersion and fume environments. Series 435 provides low permeation to H2S gas, protects against MIC and provides chemical resistance to severe wastewater environments. Contains micro-fiber reinforcement for improved film integrity.
A thick film, 100% solids, spray-applied, an abrasion-resistant coating designed for domestic wastewater immersion and fume environments. Provides excellent resistance to H2S gas permeation, protects against MIC, and provides chemical resistance to severe wastewater environments. Fiber reinforcement provides superior physical strength and higher film build.
Series 469 LavaCrete is a non-shrinking epoxy polymer concrete used for the rehabilitation of severely eroded concrete or for the corrosion proofing of new concrete where chemical resistance is required throughout the complete topping system. Extremely fast setting, allowing for rebuilds of process floors and secondary containment structures. Also used to cast sumps, drains and trenches and is an outstanding grouting material for vibration dampening in base plates and on motor pads. Series 469 kits are packaged for casting and standard placement of material. A grouting mix may be made by adjusting the kit for a more fluid application. Series 469 resin may also be used in broadcast, trowel and mat reinforced systems with a multitude of ancillary materials for services in chemical processing, wastewater, paper, power and other demanding industries.
Series 470 LavaCrete is a non-shrinking, chemical-resistant polymer concrete, enhanced for high impact and abrasion resistance. Use to rapidly rehabilitate severely damaged floors or protect new ones from impact and abrasion damage without sacrificing corrosion proofing. Use Series 470 to make a single pour on tipping floors, in metals, mining, and ore plants and where processing floors exhibit wear and damage from impact and abrasives that quickly deteriorate most standard toppings.
Series 479 is a non-shrinking novolac epoxy polymer concrete ideal for the rehabilitation of severely eroded concrete or for the corrosion-proofing of new concrete where superior chemical resistance is required throughout the complete topping system. Extremely fast setting, allowing for rebuilds of sumps, pump pads, trenches, process floors and secondary containment structures. Series 479 kits are packaged for casting and standard placement of material. A grouting mix may be made by adjusting the kit for a more fluid application. Series 479 resin may also be used in broadcast, trowel and mat reinforced systems with a multitude of ancillary materials for services in chemical processing, wastewater, paper, power and other demanding industries.
Series 489 is a durable polymer concrete which exhibits fast curing and minimal shrinkage. Ideal for the rehabilitation of severely eroded concrete or for the corrosion-proofing of new concrete where superior chemical resistance is required throughout the complete topping system. Series 489 is ideal for pump and pad rebuilds in areas of strong acid and caustic exposure. Use to cast sumps and trenches off-site for time and labor savings.
Series 490 is a durable polymer concrete which exhibits fast curing and minimal shrinkage. Ideal for the rehabilitation of severely eroded concrete or for the corrosion-proofing of new concrete where superior chemical resistance is required throughout the complete topping system. Series 490 has enhanced solvent and temperature resistance over standard vinyl ester materials. Series 490 is ideal for pump and pad rebuilds in areas of strong acid and caustic exposure. Use to cast sumps and trenches off-site for time and labor savings.
This product has been discontinued. Please refer to Series 617 | Conformal Stain WB for a suitable alternative, or contact your Tnemec Sales Representative
Conformal Stain is a penetrating, solvent-based masonry stain for horizontal concrete and virtually all vertical, above-grade concrete, precast, GFRC, exposed aggregate, stucco, terra cotta, brick and block masonry. The treatment does not alter the natural texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. Conformal Stain exhibits excellent color stability and is designed not to peel or flake when applied to a properly prepared substrate. Repels water when used on dense substrates.
Conformal Stain WB is a penetrating, water-based masonry stain for horizontal concrete and virtually all vertical, above-grade concrete, precast, GFRC, exposed aggregate, stucco, terra cotta, brick and block masonry. The treatment does not alter the natural texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. Conformal Stain WB exhibits excellent color stability, and is designed not to peel or flake when applied to a properly prepared substrate. Conformal Stain WB provides color uniformity by correcting color imperfections often found in integrally colored concrete masonry, natural stone, tilt-up and precast panels. Repels water when used on dense substrates. Conformal WB is mildew resistant and contains agents that inhibit the growth of mildew on the surface of the stain.
Phylon 1422 is a non-yellowing, acrylic coating that highlights the natural color of masonry by providing a clear, semi-gloss sheen. The treatment does not alter the natural texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. Phylon 1422 provides a durable, wet-look finish to exposed aggregate, ground-face block, sandblasted concrete and many other vertical concrete, masonry and natural stone surfaces. Repels water when used on dense substrates.
Phylon WB is a non-yellowing, water-based, acrylic coating that highlights the natural color of masonry by providing a clear, gloss sheen. Its special formulation provides a hard, durable gloss finish. The treatment does not alter the natural texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. Phylon WB provides a durable, wet-look finish to exposed aggregate, ground-face block, sandblasted concrete and many other vertical concrete, masonry and natural stone surfaces.
Phylon 624 is a unique acrylic copolymer, formulated to meet VOC requirements for curing compounds. Phylon 624 is a non-yellowing curing, sealing, hardening, dust proofing and water repellent compound that exhibits a tough, long lasting, glossy film. Phylon 624 is designed for use on exterior and interior slabs as well as above grade architectural concrete.
Conformal Clear is a penetrating, solvent-based masonry coating for virtually all vertical, above-grade concrete, precast, GFRC, exposed aggregate, stucco, terra cotta, brick and block masonry. The treatment does not alter the natural texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. Conformal Clear is designed to darken and highlight the substrate and will not peel or flake. Conformal Clear is compatible with most caulking and sealing compounds. Repels water when used on dense substrates.
Series 626 Dur A Pell GS has been formulated to provide superior protection against, and easy removal of, unwanted graffiti. This product is intended for use in conjunction with Series 680 Mark A Way to provide a complete Graffiti Protection System. Dur A Pell GS is a clear, silicone rubber based formulation, which protects vertical concrete block, brick, cast concrete, stone and other masonry substrates with little or no change to the appearance of the untreated substrate. Dur A Pell GS protects both new and existing uncoated substrates by penetrating into the pores, to prevent graffiti penetration. It has excellent stability against ultraviolet rays and salt spray and provides long-lasting protection.
Series V626 Dur A Pell GS has been formulated to provide superior protection against, and easy removal of unwanted graffiti. This product is intended for use in conjunction with Series 680 Mark A Way to provide a complete Graffiti Protection System. Dur A Pell GS is a clear, silicone rubber based formulation, which protects vertical concrete block, brick, cast concrete, stone and other masonry substrates with little or no change to the appearance of the untreated substrate. Dur A Pell GS protects both new and existing substrates by penetrating into the pores, to prevent graffiti penetration. It has excellent stability against ultraviolet rays and salt spray and provides long-lasting protection.
CT Densifyer is a clear, penetrating, water-based sealer for virtually all above-grade, horizontal, poured-in-place concrete. Concrete treated with CT Densifyer resists dusting, abrasion, wear, and damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to increase density at the surface and dustproof concrete.
This product has been discontinued. Please refer to Series 633 | Prime-A-Pell H2O for a suitable alternative, or contact your Tnemec Sales Representative
Prime-A-Pell H2O Concentrate is a concentrated water-based water repellent requiring dilution at the job site. Upon dilution, Prime-A-Pell H2O Concentrate produces a clear, filmless, penetrating water-repellent treatment for virtually all above-grade, vertical concrete, stucco, precast, sandstone and brick and block masonry. Concrete, stone and masonry treated with diluted Prime-A-Pell H2O Concentrate resist water intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and weather deterioration.
Prime-A-Pell H2O is a clear, filmless, low solids, penetrating water-based water repellent for virtually all above-grade, concrete, stucco, precast, brick, sandstone and block masonry. Concrete, stone and masonry treated with Prime-A-Pell H2O resist water intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and water deterioration.
Dur-A-Pell 20 is a clear, filmless, penetrating water repellent for virtually all above-grade, vertical and horizontal concrete, stucco, block and brick masonry and natural stone. Concrete, stone and masonry treated with Dur A Pell 20 resist water and chloride ion intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage.The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and weather deterioration.
Prime-A-Pell 200 is a clear, filmless, penetrating water repellent for virtually all above-grade, vertical concrete, stucco, block and brick masonry. Concrete, stone and masonry treated with Prime-A-Pell 200 resist water intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and weather deterioration. Prime-A-Pell 200 is manufactured utilizing a process whereby defused quartz carbide and an oligomeric siloxane are coupled, then dispersed in a hydrocarbon solvent mixture.
Prime-A-Pell Plus is a clear, filmless, penetrating water repellent for virtually all above-grade, vertical and horizontal concrete, stucco, block and brick masonry. Concrete, stone and masonry treated with Prime-A-Pell Plus resist water and chloride ion intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and weather deterioration.
Prime-A-Pell N.S. (natural stone) is a clear, filmless, penetrating water repellent for virtually all above-grade, vertical concrete and block and brick masonry and vertical and horizontal installations of natural stone. Concrete, natural stone and masonry treated with Prime-A-Pell N.S. resist water intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and weather deterioration.
This product has been discontinued. Please refer to Series 662 | Prime-A-Pell Plus for a suitable alternative, or contact your Tnemec Sales Representative
Dur A Pell 40 is a clear, filmless, penetrating water repellent for virtually all above-grade, concrete, stucco, natural stone, block and brick masonry. Concrete, stone and masonry treated with Dur A Pell 40 resist water intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and weather deterioration.
Dur A Pell 100 is a clear, filmless, penetrating water repellent for virtually all above-grade, vertical and horizontal concrete, stucco, natural stone, block and brick masonry. Concrete, stone and masonry treated with Dur A Pell 100 resist water intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and weather deterioration.
Liquid cleaner used in association with Chemprobe Series 626 and V626 Dur A Pell GS to remove graffiti from block, brick, concrete, stone and other porous masonry substrates. May also be used alone for the removal of most types of graffiti in a single application.
An advanced technology finish coat combining low VOC with exceptional performance. Offers superior color and gloss retention compared to traditional polyurethanes for long-term aesthetics on a wide range of exterior structures. Durable film stands up to abrasion and exterior weathering. Very good brush, roll and spray application characteristics. Direct-to-Metal capability allows for a labor-saving, high-build, single coat application. NOT FOR IMMERSION SERVICE.
A user friendly, low VOC, aliphatic polyurethane coating that provides excellent color and gloss retention for exterior applications to steel, concrete and other substrates in commercial, industrial, and marine environments. Direct-to-Metal capability allows for a labor-saving, high-build, single coat application.
An innovative, self-adhesive thermally insulative tape that contains a proprietary blend of insulative particles for exceptionally low thermal conductivity. Excellent for controlling condensation and providing thermal efficiency on processing equipment such as tanks, pipes, and valves. It is also a highly effective thermal break for mitigating condensation on architectural components which transmit outside temperatures through the building envelope. Series 945 Aerolon Tape is available in multiple widths that are 30 feet long and 1.5 mm thick. It can be applied in multiple layers to achieve desired thickness.
An innovative, fluid-applied, thermal insulating coating utilizing aerogel particles that imparts exceptional insulative properties to a variety of substrates. Ideal for insulating pipes, valves, tanks, structural steel, or other substrates where thermal improvement or personnel protection is desired. Part of a durable, corrosion-resistant coating system that bonds to the substrate, greatly reducing the issues associated with corrosion under insulation (CUI) and mitigating thermal bridging by controlling condensation.
A durable, easy-to-use, water-based acrylic coating that offers long-wearing protection to a variety of substrates. Excellent as a topcoat or intermediate-coat on anti-corrosive steel coating systems or when applied to concrete and drywall. Easy to apply by brush, roller, and spray, this product’s low odor and low VOC qualities make it versatile choice on architectural and industrial projects. Note: Application methods include “dry-fall” under certain conditions (see application).
Water-based, low VOC, High Dispersion Pure acrylic polymer coating providing excellent long term protection in both interior/exterior exposures. May be applied by spray, brush or roller over a variety of solvent and waterborne steel primers. May also be used over many aged coatings. It is mildew resistant and exhibits very good gloss and color stability. Series 1028 can be used for light duty wall surfaces in water treatment and pharmaceutical environments. Application methods include "dry-fall" under certain conditions (See Application). Note: Series 1028's "dry-fall" characteristics help to reduce the potential for overspray problems on buildings and surrounding property.
Water-based, low VOC, High Dispersion Pure acrylic polymer coating providing excellent long term protection in both interior/exterior exposures. May be applied by spray, brush or roller over a variety of solvent and waterborne steel primers. May also be used over many aged coatings. It is mildew resistant and exhibits very good gloss and color stability. Series 1028 can be used for light duty wall surfaces in water treatment and pharmaceutical environments. Application methods include "dry-fall" under certain conditions (See Application). Note: Series 1029's "dry-fall" characteristics help reduce the potential for overspray problems on buildings and surrounding property.
A high-solids fluoropolymer coating that provides an ultra-durable finish with user friendly brush, roll and conventional spray application. It has outstanding color and gloss retention even in the most severe exposures. Under certain conditions, it may be used to restore aged fluoropolymer coil applied coatings or for OEM applications. Fluoronar's ultra-durable film tolerates areas on steel plate that are frequently wet or experience standing water and situational immersion. Contact your Tnemec representative for more information.
A low VOC, fluoropolymer coating that provides an ultra-durable finish with user friendly brush, roll and conventional spray application. It has outstanding color and gloss retention even in the most severe exposures. Under certain conditions, it may be used to restore aged fluoropolymer coil applied coatings or for OEM applications. Fluoronar's ultra-durable film tolerates areas on steel plate that are frequently wet or experience standing water and situational immersion. Contact your Tnemec representative for more information.
A high-solids fluoropolymer coating that provides an ultra-durable finish with user friendly brush, roll and conventional spray application. It has outstanding color and gloss retention even in the most severe exposures. Under certain conditions, it may be used to restore aged fluoropolymer coil applied coatings. Contact Tnemec Technical Services or your local Tnemec representative for details.
A low VOC, fluoropolymer coating that provides an ultra-durable finish with user friendly brush, roll and conventional spray application. It has outstanding color and gloss retention even in the most severe exposures. Under certain conditions, it may be used to restore aged fluoropolymer coil applied coatings or for OEM applications. Contact Tnemec Technical Services or your local Tnemec representative for details.
A coating highly resistant to abrasion, wet conditions, corrosive fumes and exterior weathering. High build quality combines with project specific primers for two-coat, labor saving systems. Fast curing options are available; see Curing Time below. NOT FOR IMMERSION SERVICE.
A coating highly resistant to abrasion, wet conditions, corrosive fumes and exterior weathering. High build quality combines with project specific primers for two-coat, labor saving systems. Contains a blend of ultra-violet light (UV) absorbers for enhanced color and gloss retention. Fast curing options are available; see Curing Time below. NOT FOR IMMERSION SERVICE.
A coating highly resistant to abrasion, wet conditions, corrosive fumes and exterior weathering. High build quality combines with project specific primers for two-coat, labor saving systems. Fast curing options are available; see Curing Time below. Product has some applications as a direct to metal finish. Contact your Tnemec representative for more details. NOT FOR IMMERSION SERVICE.
A coating highly resistant to abrasion, wet conditions, corrosive fumes and exterior weathering. High build quality combines with project specific primers for two-coat, labor saving systems. Contains a blend of ultraviolet (UV) light absorbers for enhanced color and gloss retention. Fast curing options are available; see Curing Time below. Product has some applications as a direct to metal finish. Contact your Tnemec representative for more details. NOT FOR IMMERSION SERVICE.
A waterborne polyurethane coating that provides color and gloss retention for applications to steel, concrete and other miscellaneous substrates. It features low VOC content, low odor, high gloss finish and easy cleanup.
A waterborne polyurethane coating that provides excellent abrasion resistance and color and gloss retention for applications to steel, concrete and other miscellaneous substrates. It features low VOC content, low odor, semi-gloss finish and easy cleanup.
A unique, low odor, low VOC, water-based epoxy coating featuring HydroLink curing technology for exceptional durability and protection of steel and concrete surfaces in immersion service, including potable water and mild wastewater. Easy to apply and solvent-free, Series 1220 is an excellent choice for coating tanks, reservoirs, and basins.
An advanced generation, low odor, low VOC, high solids, water-based epoxy coating for filling surface voids in porous concrete and masonry block in interior and exterior environments. Provides high bond strength, fast curing, and rapid overcoating capabilities and can be topcoated with a variety of water- and solvent-based coatings.
Series 1402 is a food grade, vinyl ester primer for complete FDA-compliant lining systems in concrete, steel or stainless-steel tanks. Fast-cure characteristics allow for quick application of subsequent coats, limiting downtime and facility disruption. Series 1402 is the only approved primer for the ProPolymer food grade product line. Replaces ProPolymer 4808.
Series 1407 is a specially formulated primer with flexible properties designed for use on concrete and steel substrates. Series 1407 may be used under a wide-range of Tnemec vinyl ester intermediate and finish coats with the exception of direct food contact systems. Replaces ProPolymer 4805.
This corrosion resistant resin is used as the base product for many reinforced applications due to the versatility provided from the product being supplied as “neat” or non-pigmented. A versatile selection for many secondary containments and process floors, Series 1415 is best for caustic and high-ph applications, and when used as the base material for silica-free systems. Use with specialty mortar powders, to embed glass mats, as a saturant coat or as a pigmented self-leveling finish coat. Series 1415 was formerly ProPolymer 4860.
This extremely corrosion resistant coating is used as the base product for many reinforced applications due to the versatility provided from the product being supplied as “neat” or non-pigmented. Series 1416 is the best selection for strong acid conditions and when temperatures above ambient conditions are expected. Use this product to add specialty mortar powders, to embed glass mats, as a saturant coat, or as a pigmented self-leveling finish coat. Combine with LavaCrete Part C aggregate to create an enhanced corrosion resistant polymer concrete. Series 1416 was formerly ProPolymer 4847.
Resistant to very high temperature service and extremely corrosive environments, this coating is used as the base product for many reinforced applications due to the versatility provided from the product being supplied as "neat" or non-pigmented. Series 1418 is the recommended selection for use in the most chemically demanding environments, such as, wet or dry FGD scrubbers, ductwork and slurry tanks operating in elevated temperature conditions. Use with specialty mortar powders, to embed glass mats, as a saturant coat or as a pigmented self-leveling finish coat. Series 1418 was formally ProPolymer 4847HT.
Series 1420 is an FDA-compliant, trowel-grade vinyl ester lining suitable for direct-food contact in tanks and vessels. Glass-flake reinforcement provides additional abrasion and permeation resistance in wet slurry or immersion service environments. Series 1420 may be used as a stand-alone lining system or with a gel coat in a multi-coat system. Replaces ProPolymer 4855T.
Series 1422 is an FDA-compliant, trowel-grade, high temperature lining suitable for tanks and vessels in food grade service environments or where high temperature conditions are required. Highly filled with glass-flake, it is specially formulated for exceptional service in thermal cycling and chemical reaction vessels. Replaces ProPolymer 4865T.
An enhanced elevated temperature, novolac vinyl ester, filled with specially treated premium glass flakes. This product has outstanding trowel application properties. Series 1428 is ideal for the rehabilitation of heavily corroded steel substrates and for high film build protection in the most demanding chemically active and corrosive environments. Series 1428 can be used in FGD units for time saving, quick repairs on small areas or used as a complete lining. Formerly ProPolymer 4875T.
Series 1430 is an FDA-compliant, mineral flake-filled vinyl ester lining for food grade tanks, vessels and other structures. Applied by spray or roller, it can be used as either a stand-alone lining system or as a topcoat for added protection over trowel applied vinyl ester linings. Replaces ProPolymer 4813S.
Series 1432 is an FDA-compliant, vinyl ester lining for food grade tanks, vessels and other structures. Highly filled with glass flake, Series 1432 is specially formulated to provide exceptional service in thermal cycling and chemical reaction tanks and vessels. Applied by roller or spray, it may be used as a stand-alone lining system or as a topcoat for added protection over trowel applied vinyl ester linings. Replaces ProPolymer 4822S.
Continue Exploring in the color tool
When you finish selecting, request your Swatch Packet below. Expect your swatch cards in 5-7 business days. Contact your expert Sales Rep at any time.
You can use our Color Tool page to explore our available colors and request swatches of colors you like.
Sorry, there is a maximum of 6 color swatches.